Home > News > Content
Polyacrylamide Process And Equipment Requirements
Jul 28, 2017

Polyacrylamide PAM selection should focus on the following aspects: Generally speaking, Polyacrylamide anionic products and non-ionic products for alkaline, neutral or weak acid, the main material for the inorganic sludge, and the higher the solid content. The greater the amount of flocculant used. Polyacrylamide The molecular weight of the flocculant is selected according to the floc size required for the process. The flocculant must be dissolved and mixed with the sludge before treatment. ) Can improve the floc strength by increasing the molecular weight of the flocculant. The degree of hydrolysis of the flocculant must be screened by experiment. Polyacrylamide The choice of flocculant must take full account of the requirements of the process and equipment.

Sludge dewatering agents are generally cationic polyacrylamide. Urban sewage treatment of urban sewage is usually used biological and physical law into the line, in which the biological method is widely used because of the high efficiency. Polyacrylamide PAM flocculants can be used in all stages of municipal wastewater treatment. Such as primary sedimentation treatment, secondary sedimentation treatment and concentration, the most widely used sludge dewatering stage. Add flocculants to increase the rate of sludge treatment. Reduce the moisture content of the sludge cake. Reduce the sludge volume and so on. The formation of floc filter good advantages. Anionic polyacrylamide is commonly used in the following common processes in wastewater treatment: wastewater pretreatment, Polyacrylamide post-treatment, including pretreatment including adsorption filtration, etc. Post-treatment Depending on the nature of the wastewater, oxidation, biological treatment, flotation and so on can be used. Due to the wide range of industrial effluents, the pollutants contained therein are very complex. The nature of the sewage varies greatly. Therefore, the selection and use of specific industrial wastewater treatment must be determined by a large number of laboratory tests and field tests. Polyacrylamide Polyacrylamide must be dissolved at a low temperature, a certain temperature and then add a row, the type of product and dosage should be based on water quality and water purification technology characteristics. By experiment. Polyacrylamide PAM adsorption bridging ability, with a number of functional groups, flocculation effect is good, wide range of applications, less dosage, resulting in less sludge.

Sometimes according to the actual production situation, Polyacrylamide two or three flocculants in combination. The effect of anionic polyacrylamide flocculant is affected by many factors such as PH value of sewage, content of suspended solids, temperature and so on. The current flocculant unsafe and secondary pollution more and more attracted the attention of society. Polyacrylamide itself is not toxic. But some products which do not respond to the residual monomer toxicity is great. Therefore, the products used for drinking water treatment of its content in the water has a strict, the current product residual monomer content requirements below 0.05. Water Treatment Water purification processes include concentration, sedimentation, flotation and filtration. In most cases it is required to add a coagulant before adding flocculant. Thereby producing a large volume of floc to increase the rate of solid-liquid separation. Polyacrylamide Industrial water in the case of low demand only need to concentrate and settle.

1, the polyacrylamide for drilling mud, with thickening, Polyacrylamide stabilization and sedimentation flocculant effect. PAM is added to the drilling mud to increase the consistency of the slurry. Speaking of the role of stability is reflected in: not only can improve the levitation force, but also has the role of control of water loss, thereby enhancing the speed of cementing. Such as colloidal polyacrylamide, also known as flocculant polyacrylic acid amine is used as oil field water injection thickener and drilling low solid phase non-dispersible mud flocculant, Polyacrylamide and anionic polypropylene phenol (PHP) is used as oil field mud treatment agent, Thickener

2, in the process of mining oil, the injection of water in the role of polyacrylamide viscosity increase, this way, can effectively avoid the breakdown of the oil layer, Polyacrylamide thereby improving the oil recovery rate;

3, in the production wells, injection wells for water and oil than control agents, polyacrylamide solution or organic crosslinking agent, polyvalent metal ions, Polyacrylamide formaldehyde resin and other water-insoluble type of gel-type gel, for oil, Control the water effluent.

4, PAM can also be used as fracturing fluid additives, the main purpose is to increase the viscosity, improve the ability of sand suspension, reduce the loss, reduce friction; 

5, for pipe wall lubricant, Jiang Zuji and anti-wax agent.